Your Cart

BSP-360 Industrial solar controller with 4 ports POE 802.3at managed switch

BSP-360 Industrial solar controller with 4 ports POE 802.3at managed switch
BSP-360 Industrial solar controller with 4 ports POE 802.3at managed switch

Solar  Controller, Renewable Energy Industrial 802.3at PoE Managed Ethernet Switch, BSP-360, is designed for deploying a surveillance or wireless network and remotely monitoring and managing the IP-based devices. Based on its green technology, the BSP-360 can be charged by the inexhaustible and natural source of energy, such as solar, wind and hydroelectric power to conserve energy so as to economically power these remote IP cameras and wireless APs, especially used for such expansive applications as dams, forests, deserts, national parks, nature/animal protection areas and highways.

Physical Port

•5-port 10/100/1000BASE-T Gigabit RJ45 copper with 4-port IEEE 802.3at/af PoE Injector (Port 1 to Port 4)

•RJ45 type interface for basic management and setup

•USB type A female for setting file backup and restore

Power over Ethernet

•Complies with IEEE 802.3at Power over Ethernet Plus end-span PSE

•Backward compatible with IEEE 802.3af Power over Ethernet

•Up to 4 ports of IEEE 802.3af/802.3at devices powered

•Supports PoE power up to 30 watts for each PoE port

•Auto detects powered device (PD)

•Circuit protection prevents power interference between ports

•Remote power feeding up to 100 meters

•PoE management

 - Total PoE power budget control

 - Per port PoE function enable/disable

 - PoE port power feeding priority

 - Per PoE port power limitation

 - PD alive-check

 - PoE schedule

Battery Management

•Battery type option: Nickel-cadmium battery or lead-acid battery

•Easy diagnostic of the system operating status via LED indicator

•Battery current usage and status

•Battery capacity and power consumption statistics

•Low voltage cut-off protection: Send alert and cut off the low priority PoE port for the low power battery

•Pulse Width Modulation (PWM) Protection

 - Reverse current protection to prevent the current circuits from flowing back to the PV panel

 - Over-current and over-temperature protection

 - Reverse polarity protection (for battery and charging electrodes)

Industrial Case & Installation

•IP30 aluminum case

•DIN-rail and wall-mounted design

•Supports -10 to 60 degrees C operating temperature 

•Supports ESD 6KV DC Ethernet protection 

•Redundant power design

 - 24V~45V DC wide power input 


•Hardware based 10/100Mbps (half/full duplex), 1000Mbps (full duplex), auto-negotiation and auto MDI/MDI-X

•Features Store-and-Forward mode with wire-speed filtering and forwarding rates

•IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation

•8K MAC address table size

•Automatic address learning and address aging


•Internet types: Dynamic IP, static IP, PPPoE, L2TP, PPTP

•Static and dynamic (RIP1 and 2) routing

•IP/MAC-based bandwidth control

•Supports Port Forwarding, DMZ, UPnP and Dynamic DNS for various networking applications

•802.1d STP and IGMP Proxy


•Port filtering lets you either allow or prevent which applications can access the Internet.

•MAC filtering allows you to include or exclude computers and devices based on their MAC address

•URL filtering allows you to control access to Internet websites in an URL list

•IP source guard prevents IP spoofing attacks

•DoS attack prevention


•Switch Management Interface

 - IPv4 Web switch management 

 - SNMP v1, v2c 

•Static and DHCP for IP address assignment

•System Maintenance

 - Firmware upload/download via HTTP

 - Configuration upload/download through HTTP

 - Hardware reset button for system reboot or reset to factory default

•NTP Network Time Protocol

•SNMP trap for interface Link Up and Link Down notification

•Event message logging to remote syslog server

•PLANET Smart Discovery Utility



Hardware Specifications 

Copper Ports  LAN: 5 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 1 to Port 5, bridge mode)

 WAN: 1 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 5, gateway mode) 


PoE Injector Port 4 ports with 802.3af/802.3at PoE injector function (Port 1 to Port 4) 

USB 1 USB Type A female for setting backup 

Power Output 4 PoE out 51VDC; max. 30 watts per PoE port

 2 DC out 24@ 1A maximum (four-pin terminal block)

* The voltage of DC out is based on the battery.


Switch Architecture Store-and-Forward  

Switch Fabric 10Gbps/non-blocking 

Switch Throughput@64 bytes 5.95Mpps@64 bytes 

MAC Address Table  8K entries  

Shared Data Buffer 512Kbit 

Flow Control  IEEE 802.3x pause frame for full-duplex

 Back pressure for half-duplex 


Reset Button < 5 sec: System reboot

 > 5 sec: Factory default


LED 3 LEDs for System and Power: 

•Green: Power 

•Green: Fault

•Green: System

 4 LEDs for PoE Copper Ports (Port 1~Port 4):

•Green: LNK/ACT

•Orange: PoE-in-use

 1 LED for 10/100/1000T Copper Port (Port 5):

•Green: LNK/ACT

 3 LEDs for PoE Power Usage (W)

•Green: 50, 100 and 120W


Connector Removable 6-pin terminal block

 Pin 1/2 for PV panel; Pin 3/4 for alarm; Pin 5/6 for battery


Alarm 1 Digital Output (DO):

 Level 0: -24V~2.1V (±0.1V)

 Level 1: 2.1V~24V (±0.1V)

 Open collector to 24V DC, 100mA max.


Power Requirements PV in: 24~45V DC

 Battery in/out: 24V DC


Power Consumption/ Dissipation 5.04 watts, 17.1BTU (Standby without PoE function)

 6.96 watts, 23.7 BTU (Full loading without PoE function)

 135.36 watts, 461.5 BTU (Full loading with PoE function)


Dimensions (W x D x H) 84 x 107 x 152 mm 

Weight 1026g 

ESD Protection 6KV DC 

Enclosure IP30 aluminum case 

Installation DIN-rail kit and wall-mount ear  

Power over Ethernet 

PoE Standard IEEE 802.3af/802.3at Power over Ethernet PSE 

PoE Power Supply Type End-span  

PoE Power Output Per port 51V DC, 275mA. Max. 15.4 watts (IEEE 802.3af)

 Per port 51V DC, 535mA. Max. 30 watts (IEEE 802.3at) 


Power Pin Assignment 1/2 (+), 3/6 (-) 

PoE Power Budget 120 watts (PoE consumption + DC out and depending on power input) 

Max. Number of Class 2 PDs 4 

Max. Number of Class 3 PDs 4 

Max. Number of Class 4 PDs 4 

Electrical Characteristics 

System Voltage Rating 24V DC 

Maximum Charging Current 6A 

Max. Solar Array VOC 60V DC 

Max. Operating Voltage  45V DC 

Total Current Consumption While operating -32mA

 At idle -11mA


High Temperature Shutdown 100 degrees C disconnect solar and load

 80 degrees C reconnect solar and load


Battery Charging Characteristics 

Charge Algorithm Bulk charge (constant current), Absorption charge (constant voltage) and Floating charge. Absorption and Floating charge with PWM protection. 

Maximum Output Current 6A 

Nickel-cadmium Battery ± 40 mV/degrees Celsius for NiCad type batteries; charge cut-off @ 55 degrees C

 (Temperature compensation baseline@ 25 degrees C)


Lead Acid Battery (Default Setting) ± 60 mV/degrees Celsius for lead acid type batteries; charge cut-off @ 55 degrees C

 (Temperature compensation baseline@ 25 degrees C)


Float Charge Voltage DC 27.2V (26.0~30.0V) 

Absorption Charge Voltage DC 29.2V (28.0~32.0V) 

LVD (Low Voltage Disconnection) DC 22.2V (21.0~25.0V) 

LVR (Low Voltage Reconnection) DC 24.8V (23.0~27.0V) 

Router Features 

Internet Connection Type Shares data and Internet access with users, supporting the following internet accesses:


•Dynamic IP

•Static IP




Firewall NAT firewall with SPI (Stateful Packet Inspection)

 Built-in NAT server supporting Port Forwarding, and DMZ

 Built-in firewall with IP address/MAC address/Port/ URL filtering

 Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter, DoS protection


Routing Protocol Static/Dynamic (RIP1 and 2) routing 

VPN Pass-through PPTP, L2TP, IPSec, IPv6 

LAN Built-in DHCP server supporting static IP address distribution

 Supports UPnP, Dynamic DNS

 Supports IGMP Proxy

 Supports 802.1d STP (Spanning Tree)

 IP/MAC-based bandwidth control



Management Interface Setup of system/management functions

 Web firmware upgrade

 SNMP trap for alarm notification of events


PoE Management Power limit by consumption and allocation

 PoE admin mode

 Per port power schedule

 Per port power enable/disable

 Power feeding priority

 Current per port usage and status

 Total power consumption

 PD alive check

 Scheduled power recycling


Battery Management Battery current usage and status 

 Battery capacity statistics

 Low Voltage Cut-Off Protection


Standards Conformance  

Regulatory Compliance  FCC Part 15 Class A, CE  

Standards Compliance  IEEE 802.3 10BASE-T Ethernet

 IEEE 802.3u 100BASE-TX Fast Ethernet

 IEEE 802.3ab 1000BASE-T Gigabit Ethernet

 IEEE 802.3x Flow Control and Back Pressure

 IEEE 802.1D Spanning Tree Protocol

 IEEE 802.3af Power over Ethernet 

 IEEE 802.3at Power over Ethernet Plus

 RFC 768: UDP

 RFC 791: IP

 RFC 2068 HTTP

 RFC 1157: SNMP v1

 RFC 1902: SNMP v2c

 RFC 5424: Syslog



Operating Temperature: -10 ~ 60 degrees C

 Relative Humidity: 5 ~ 95% (non-condensing)


Storage Temperature: -10 ~ 70 degrees C

 Relative Humidity: 5 ~ 95% (non-condensing)