Your Cart

NV-600W - Wireless VDSL2 Router (CPE)

NV-600W - Wireless VDSL2 Router (CPE)
NV-600W - Wireless VDSL2 Router (CPE)

Saratota Suggest NV-600 Kit Options

  • NV-600L (CO) / NV-600A (CPE)
  • NV600L (CO) / NV-600W (CPE) - Wireless


NV-600W is an VDSL2 802.11n Wireless router equipped with four Gigabit LAN ports. It is compliant to ITU-T G.993.2 and G.993.5 standards and supports VDSL2 profile 30a that features 100Mbps of symmetric data. With built-in 802.11n technology, it can deliver wireless speeds up to 300Mbps and is perfectly suitable for triple-play applications. NV-600W is designed to meet the ISPs requirements with future proof Vectoring and ADSL2+ compatibility to cover end users in different loop range areas.

Vectoring Technology friendly Mode support

Vectoring is a transmission method that employs the coordination of line signals for reduction of crosstalk levels and improvement of performance. It is based on the concept of noise cancellation, much like noise-cancelling headphones. The ITU-T G.993.5 standard, "Self-FEXT cancellation (vectoring) for use with VDSL2 transceivers" (2010), also known as G.vector, describes vectoring for VDSL2. The scope of Recommendation ITU-T G.993.5 is specifically limited to the self-FEXT (far-end crosstalk) cancellation in the downstream and upstream directions. The far end crosstalk (FEXT) generated by a group of near-end transceivers and interfering with the far-end transceivers of that same group is cancelled. This cancellation takes place between VDSL2 transceivers, not necessarily of the same profile.

Easy Installation

The NV-600W may be installed on any level surface (e.g. a table or shelf). NV-600W supports plug-and-play installation and is fully compatible with all kinds of network protocols. Furthermore, user can watch the status of each individual port via the LED indicators.

Enhanced Management

For efficient management, via Web interface, the NV-600W can be programmed for advanced management functions such as QoS (Quality of Service)/DSCP, IEEE 802.1q Tag VLAN, SNMP v1/v2c/v3, IGMP v3 and enhanced security functions such as Packet filtering, DMZ, Mac Address based filtering, Parental Control, Application based filtering. NV-600W also support wireless security such as WEP, WPA, WPA2, TKIP, AES.


• Supports ITU-T G.993.5 Vectoring
• Compliant with IEEE 802.11b/g/n wireless standard with 2T2R (Up to 300 Mbps)
• Supports standard WPS, PIN, PBC
• Supports WEP, WPA, WPA2, TKIP, AES
• Supports QoS-WMM, WMM-PS
• Low power with Advanced Power Management
• Supports ATM and PTM transmission mode auto detection( ADSL Annex B backward compatible)
• Supports high bandwidth up to 100Mbps symmetric over line ports
• Supports 8a, 8b, 8c, 8d, 12a, 12b, 17a, 17b, and 30a band profile and 997, 998 band plan
• Supports ATM-TC,ATM and AAL5 (ATM Flow Throughput / OAM Cell Filter and Forwarding / AAL5 SAR:PVC / ATM   Traffic Class / ATM PVC Shaping / ATM PVC Scheduling)
• Supports ATM Total Upstream Priority Queues
• Supports uPnP/PPPoE/PPPoATM/IPv4/IPv6/NAT/NAPT
• Supports static routing for IPv4 and IPv6 forwarding
• Supports Firewall functions contains Packet filtering, DMZ, Mac Address ased filtering, Parental Control, Application   based filtering
• Supports DHCP Server/DHCP Relay/DHCP Client/DHCPv6 Client/DHCPv6 Server/DNS/DNS Proxy or   Relay/DNSv6 Proxy or Relay/NTP Client/HTTP1.1 server
• Supports Multicast IP table/IGMP v3 Proxy and Snooping
• Supports IEEE 802.1p VLAN Priority and mapping to DSCP
•Supports 802.1q Tag Vlan/Port base Vlan
• Supports HTTP/HTTPS(SSL) web management
• Supports remote management and monitor
• Supports configuration backup and restore
• Provides surge protection for Line port
• Supports Router & Switch(Bridged) mode selection
• Supports jumbo frame up to 1680 bytes
• Supports 8 queue MFC/DSCP both type QoS
• Supports Dual Firmware Image Backup
• Supports Dying Gasp
* Specifications are subject to change without prior notice


LAN Distance Extension
The NV-802S/NV-600W is good for Ethernet distance extension over existing telephone wires. With just one pair of AWG-24 copper wire, you can easily connect the maximum data rate of 100Mbps and up to 3km distance support. It is easy-to-use which do not requires installation of additional wiring. Every modular phone jack in the building can become a port on the LAN.



 Standard Conformance
 IEEE802.3/802.3u/802.3z/802.11b/802.11g/802.11n standards
 ITU-T G992.1/G992.3/G992.5/G993.1/G997.1/G993.2 standards

 Regulatory Compliance:


 RoHS compliance

 Hardware Specifications
 Physical Interface:

 4 x RJ-45 10/100/1000Mbps auto-negotiation Ethernet port
 1 x RJ-11/Terminal Block connector for VDSL2 line port

 1 x RJ-11 connector for POTS/ISDN device

 2 x 2dBi Antennas (5dBi antennas optional)

 1 x Reset Button (Factory Reset)

 1 x WPS Button

 LED indication:

 1 x Power LED
 4 x Link/Active Status for Ethernet port
 1 x Link LED for VDSL2 port

 1 x WPS LED


 Wireless Frequency Range:
 Switch method:
 Store and forward
 Flow control:
 Full duplex: IEEE 802.3x
 Half duplex: Back pressure
 Typical Power Consumption:
 Power Supply:
 Input Voltage: 12 VDC
 Operating Temperature:
 0°C ~ 50°C (32°F ~ 122°F) Fanless, free air cooling
 Storage Temperature:
 -20°C ~70°C (-4°F ~ 158°F)
 10 to 90% (non-condensing)
 184 x 158 x 104 mm (7.2" x 6.22 " x 4.1") with 2dBi Antenna
 About 0.44 kgs
 Lantiq VRX


* Specifications are subject to change without prior notice